陶瓷马桶水箱 - 概述

Ceramic Toilet Flush Tanks are made from special clay that is both waterproof and porous on the inside. During manufacturing, the clays are first baked and dried in a kiln to make them hard. Then, the kilns are fired again to finish the process by burning the glaze. The resulting ceramic becomes glassy and waterproof. The next step involves assembling the sections of the toilet and glazing them.

When constructing a new toilet, one must consider the materials used. Earlier, toilets were wrapped with ornately carved wood. Today, however, toilets are typically made of porcelain, a type of ceramic that is also used for dishwater and pots. The material is actually a combination of ingredients that are commonly found in clay, including kaolin, silicate minerals, and powdered feldspar. When combined, the materials form a thick, clay-like slurry.

The construction process of a
ceramic toilet flush tank
is quite similar to that of a normal toilet. Both types of tanks are made using the same process. The float is on an arm that connects to the fill valve. The fill valve shuts off when the float reaches a pre-determined height. If the float reaches the maximum height, it closes off the fill valve. This ensures that the tank always has water, which is necessary for flushing and cleaning.

Unlike traditional flush tanks, toilets with a ceramic toilet flush tank can be maintained easily. Regular maintenance is necessary to maximize the water savings. The forward jet connection on a traditional tank can become clogged over time due to particles and wear. Even if the air vent in the bowl is open, there is a chance that the forward jet connection will clog. Therefore, it is important to replace the flushing system in your toilet.

这些马桶采用不同的黏土制成，黏土在注入前会先过筛。烧制完成后，每个铸件都会逐一检查是否有裂纹和变形。虽然对马桶进行随机抽样检查并不是判断质量的好方法，但却是发现马桶是否有裂纹的有效途径。

大多数马桶都配有与便器相连的水箱冲水系统。水箱内储存固定体积的水。抽水马桶包含两个机制：第一个装置用于将部分水快速排入便器。冲水时，水箱中的水被冲入排水管。这一机制使冲水系统更加高效。建议将水位填充至溢流管下方1/4英寸处。

马桶的浮球是调节水箱水位的机制。当浮球下降时，它会抬起阀门将水冲入便器；当浮球到达满水位时，阀门关闭。需要注意的是，马桶是实心瓷制品，可能出现裂纹。但在某些情况下，细小的发丝裂纹可以使用硅胶管道环氧树脂进行修复。

一小时后移除顶部芯模。边缘模具包含安装储水箱的位置，并设有用于连接冲洗喷嘴的孔洞。边缘部件设有安装孔和阀门孔。完成后，移除顶部芯模。边缘部件是马桶的底部部分，包含马桶边缘。

陶瓷马桶的制造过程涉及复杂的生产工艺。它们通常以简洁为设计理念。马桶的冲水机制在其完成后安装。整个过程由水管工完成。浮球固定在座圈上，并用螺栓固定。浮球和座圈并非永久连接。这些部件可单独销售，也可由水管分销商组装。

入墙式冲水马桶系统是现代浴室设计的经典之作。这些系统在全球已被安装超过一百万次。标准冲水的水量为1.6美制加仑。双冲式马桶使用0.9美制加仑。此外，它们每年可节省数千加仑的水。除了安装高效陶瓷马桶的好处外，这种水箱风格的许多其他优点还包括其耐用性和可靠性。